X-Git-Url: http://git.scottworley.com/tattlekey/blobdiff_plain/a36c278f05a806c9ced1a96b04eae0e6b9d8a5d5..48e03c9c42becd6010156318c1436cc061e61e3f:/client/config.c

diff --git a/client/config.c b/client/config.c
index 0e1a86d..a708df4 100644
--- a/client/config.c
+++ b/client/config.c
@@ -1,29 +1,46 @@
 #include "config.h"
 
 /* Wi-Fi credentials */
-char config_wifi_ssid[] = "THEWIFISSID";
-char config_wifi_pass[] = "THEWIFIPASSWORD";
+const char config_wifi_ssid[] = "THEWIFISSID";
+const char config_wifi_pass[] = "THEWIFIPASSWORD";
 
 /* Network address of the server to contact */
-char config_tattle_server_ip_address[] = "192.168.10.10";
-u16_t config_tattle_port = 29803; // 'tk'
+const char config_tattle_server_ip_address[] = "192.168.10.10";
+const u16_t config_tattle_port = 29803; // 'tk'
 
 /* For distinguishing reports from multiple tattlekey devices. */
-u16_t config_this_tattler_identity = 1;
+const u16_t config_this_tattler_identity = 1;
 
 /* Which GPIO pin is the button connected to?
  * The button should span this pin and ground, connecting this pin to ground
  * when pressed.
  * https://projects.raspberrypi.org/en/projects/introduction-to-the-pico/10
  * recommends pins 18, 22, or 28. */
-uint config_button_pin = 18;
+const uint config_button_pin = 18;
 
 /* Don't bother reporting each separate button press when it is pressed many
  * times in short succession.  (We also use this to de-bounce. :) */
-u32_t config_minimum_seconds_between_button_presses = 1;
-
-/* Send each report multiple times. */
-uint config_resend_count = 5;
+const u32_t config_minimum_seconds_between_button_presses = 1;
+
+/* Send each report multiple times. Re-sends are sent with exponential delay:
+ *   #1 sent immediately
+ *   #2 after 1 seconds
+ *   #3 after 2 seconds
+ *   #4 after 4 seconds
+ *   #5 after 8 seconds
+ *   ...
+ *   #11 after 8 minutes
+ *   #12 after 17 minutes
+ *   #13 after 34 minutes
+ *   #14 after 68 minutes
+ *   #15 after 2 hours
+ *   #16 after 4 hours
+ *   #17 after 9 hours
+ *   etc.
+ * This provides some robustness against network outages, automatically
+ * replaying the log periodically to be collected after connectivity
+ * is restored. */
+const uint config_resend_count = 16;
 
 /* These control the size of the per-send-count press queues.
 When the button is pressed more than config_maximum_queue_size times
@@ -33,9 +50,9 @@ the old, longest-delayed, most-redundant reports that get dropped;
 fresh, timely reports of new button presses will not get anywhere near
 config_resend_count in a resend interval because the early resend internals
 are so short.  */
-uint config_maximum_queue_size = 512;
+const uint config_maximum_queue_size = 512;
 
 /* This is paranoia about unanticipated delays.  Setting this to zero
 would probably be fine, but imposing a minimum queue size is an easy
 safety measure. */
-uint config_minimum_queue_size = 32;
+const uint config_minimum_queue_size = 32;